Print This Page

Light Cutting Oil

Material Safety Data Sheet

Information on this form is furnished solely for the purpose of compliance with the Occupational Safety and Health Act and shall not be used for any other purpose. Black Swan Manufacturing Co. urges the customers receiving this Material Safety Data Sheet to study it carefully to become aware of the hazards, if any, of the product involved. In the interest of safety, you should notify your employees, agents, and contractors of the information on the sheet.

SECTION I - GENERAL INFORMATION
Black Swan Manufacturing Co.
4540 W. Thomas Street
Chicago, IL 60651-3318
Telephone No: 1-773-227-3700
Fax No: 1-773-227-3705

For chemical emergencies during
transportation only call

INFOTRAC
1-800-535-5053
24 hours per day - 7 days a week
Date Prepared

01/01/08

 		Trade Name

LIGHT CUTTING OIL

SECTION II - HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
HAZARDOUS COMPONENTS    CAS#     APPROX%   ACGIH-TLV OSHA-PEL
SEVERELY HYDROTREATED

HEAVY NAPHTHENIC OIL    64742-52-5     >90         5 MG/M3       5 MG/M3

SULFURIZED FATS                68991-70-8       <5                N/E              N/E

DI-TERTIARY NONYLPOLYSULFIDE   68425-16-1     <2     N/E         N/E

CHLORINATED PARAFFIN  63449-39-8       <1                 N/E             N/E
*Title III Section 313 Supplier Notification: this product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency planning and community Right-to-Know Act of 1966 and of 40CFR372. This information must be included in all MSDS’s that are copied and distributed for this material.

SHIPPING INFORMATION

NOT HAZARDOUS FOR SHIPPING PURPOSES.

 

 

 

SPECIAL HAZARD DESIGNATIONS

HMIS HAZARD RATING
HEALTH 1 0 - MINIMAL
FLAMMABILITY 1 1- SLIGHT
REACTIVITY 0 2- MODERATE
PROTECTIVE X 3- SERIOUS
EQUIPMENT 4- SEVERE

SECTION III - PHYSICAL DATA
APPEARANCE

CLEAR COLORED LIQUID

 		ODOR

BLAND ODOR

 		BOILING POINT

>500 DEG. F
SPECIFIC GRAVITY (H2O=1)

0.9 AT 60 DEG. F

 		VAPOR PRESSURE (mm Hg.)

<0.1 AT 20 DEG. C

 		VOLATILE BY VOLUME (%)

N/A
VAPOR DENSITY (AIR=1)

>1.0

 

 EVAPORATION RATE (BUAC=1)

NEGLIGIBLE

 		SOLUBILITY IN WATER

NIL

SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT ( METHOD USED) FLAMMABLE LIMITS LEL UEL
>300 DEG. F (PERCENT BY VOLUME) N/A N/A
FIRE EXTINGUISHING MEDIA

WATER FOG, CO2 FOAM, DRY CHEMICAL.
SPECIAL FIRE FIGHTING PROCEDURES

PROPER RESPIRATORY EQUIPMENT TO PROTECT AGAINST THE HAZARDOUS EFFECTS OF COMBUSTION PRODUCTS IS RECOMMENDED. WATER IN A STRAIGHT HOSE STREAM MAY CAUSE FIRE TO SPREAD AND SHOULD BE USED AS A COOLING MEDIUM ONLY.
UNUSUAL FIRE AND EXPLOSION HAZARD

MISTS OR SPRAYS COULD IGNITE AT TEMPERATURES BELOW THE INDICATED FLASH POINT. KEEP IGNITION SOURCES, OPEN FLAMES, ETC. AWAY FROM THESE FUMES.

SECTION V - HEALTH HAZARD DATA
PRIMARY ROUTES OR ENTRY __X___Inhalation ______Skin contact ______Eye contact __X___Ingestion
EFFECT OF OVEREXPOSURE

EYES: NO SIGNIFICANT EFFECTS BEYOND MINOR IRRITATION ARE EXPECTED.

SKIN: MODERATE IRRITATION AND DISCOMFORT. DEFATTING OF SKIN AND REDNESS ARE POSSIBLE. TOXIC SYSTEMIC EFFECTS FROM ABSORPTION ARE EXPECTED TO BE MINOR.

INHALATION: MODERATE RESPIRATORY DISCOMFORT AND/OR HEADACHES. TOXIC SYSYTEMIC EFFECT FROM INHALATION ARE EXPECTED TO BE MINOR.

INGESTION: GASTROINTESTINAL TRACT IRRITATION AND/OR DISCOMFORT IS POSSIBLE.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE

PRE-EXISTING DERMATITIS OR SKIN DISEASES.
EMERGENCY AND FIRST AID PROCEDURES

EYES: FLUSH EYES WITH PLENTY OF WATER FOR 15 MINUTES. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR PERSISTS.

SKIN: WASH EXPOSED AREA WITH MILD SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR PERSISTS.

INHALATION: FRESH AIR SHOULD ALLEVIATE ANY RESPIRATORY DISCOMFORT. IF BREATHING DIFFICULTIES DEVELOP OR PERSIST, GET MEDICAL ATTENTION.

INGESTION: DO NOT INDUCE VOMITING. DANGER FROM ASPIRATING INTO LUNGS EXCEEDS SHORT TERM TOXIC EFFECTS. GET IMMEDIATE MEDICAL HELP.

SECTION VI - REACTIVITY
STABILITY UNSTABLE   CONDITIONS TO AVOID

EXPOSURE TO EXCESSIVE HEAT, OPEN FLAMES AND SPARKS. AVOID CONDITIONS THAT FAVOR THE FORMATION OF EXCESSIVE MISTS AND/OR FUMES.
  STABLE X  
INCOMPATIBILITY (MATERIALS TO AVOID)

AVOID STRONG OXIDIZING MATERIALS.
HAZARDOUS DECOMPOSITION PRODUCTS
OXIDES OF CARBON & SULFUR.
HAZARDOUS POLYMERIZATION MAY OCCUR   CONDITIONS TO AVOID
WILL NOT OCCUR X N/A

SECTION VII - SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED

EXTINGUISH POSSIBLE SOURCES OF IGNITION AND VENTILATE SPILL AREA. DIKE AREA TO CONTAIN SPILL AND CLEAN UP BY ABSORBING ON AN INERT ABSORBENT OR OTHER CONVENIENT MEANS.

DO NOT FLUSH INTO SEWERS OR NATURAL WATERWAYS. NON-ESSENTIAL PERSONNEL SHOULD NOT ENTER AREA DUE TO SLIPPING HAZARDS.
WASTE DISPOSAL METHOD

CONDITIONS OF USE MAY CAUSE THIS MATERIAL TO BECOME A HAZARDOUS WASTE AS DEFINED BY STATE OR FEDERAL LAW. USE APPROVED TREATMENT, TRANSPORTERS AND DISPOSAL SITES.

SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION (Specify type)

USE NIOSH/MSHA APPROVED RESPIRATORS WHEN VAPORS OR MIST CONCENTRATIONS EXCEED PERMISSIBLE EXPOSURE LIMITS.
VENTILATION

USE LOCAL EXHAUST OR DILUTION VENTILATION AS APPROPRIATE TO CONTROL VAPOR OR MIST TO BELOW PERMISSABLE EXPOSURE LIMITS.
PROTECTIVE GLOVES

NEOPRENE RUBBER OR OTHER CHEMICAL RESISTANT MATERIAL.

 		EYE PROTECTION

CHEMICAL SAFETY GOGGLES WITH SPLASH SHIELDS.
OTHER PROTECTIVE EQUIPMENT AND HYGIENIC PRACTICES

CHEMICAL RESISTANT BOOTS, APRON, ETC. AS NECESSARY TO PREVENT CONTAMINATION OF CLOTHING AND SKIN CONTACT.

SECTION IX - SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING

STORE IN A COOL, DRY, VENTILATED AREA AWAY FROM EXCESSIVE HEAT, SPARKS AND OPEN FLAMES. AVOID PROLONGED OR REPEATED CONTACT WITH SKIN AND/OR BREATHING OF VAPORS WHEN HANDLING. KEEP CONTAINERS CLOSED WHEN NOT IN USE. DO NOT STORE WITH OXIDIZING AGENTS.
OTHER PRECAUTIONS

FOLLOW RECOMMENDED PROCEDURES WHEN WORKING WITH COMBUSTIBLE PETROLEUM LIQUIDS.

PRODUCT CAN BE MADE TO BURN. AVOID EXCESSIVE MIST AND/OR AEROSOL FORMATION.
This information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof.