Print This Page

Silicone Sealant

Material Safety Data Sheet

Information on this form is furnished solely for the purpose of compliance with the Occupational Safety and Health Act and shall not be used for any other purpose. Black Swan Manufacturing Co. urges the customers receiving this Material Safety Data Sheet to study it carefully to become aware of the hazards, if any, of the product involved. In the interest of safety, you should notify your employees, agents, and contractors of the information on the sheet.

SECTION I - GENERAL INFORMATION
Black Swan Manufacturing Co.
4540 W. Thomas Street
Chicago, IL 60651-3318
Telephone No: 1-773-227-3700
Fax No: 1-773-227-3705

For chemical emergencies during
transportation only call

INFOTRAC
1-800-535-5053
24 hours per day - 7 days a week
Date Prepared

01/01/08

 		Trade Name

SILICONE SEALANT

SECTION II - HAZARDOUS INGREDIENTS / IDENTITY INFORMATIONC
HAZARDOUS COMPONENTS   CAS# APPROX% ACGIH-TLV OSHA-PEL
METHYLTRIACETOXYSILANE 004153343 2 NONE ESTABLISHED NONE ESTABLISHED
ETHYLTRIACETOXYSILANE 017689779 2 NONE ESTABLISHED NONE ESTABLISHED
SILICA 007631869 10 10 MG/M3 NONE ESTABLISHED

*Title III Section 313 Supplier Notification: this product contains toxic chemicals subject to the reporting requirements of Section 313 of the Emergency planning and community Right-to-Know Act of 1966 and of 40CFR372. This information must be included in all MSDS's that are copied and distributed for this material.

SHIPPING INFORMATION

 

NOT HAZARDOUS FOR SHIPPING PURPOSES.

 

SPECIAL HAZARD DESIGNATIONS

HMIS NFPA HAZARD RATING
HEALTH 1 1 0 - MINIMAL
FLAMMABILITY 1 1 1- SLIGHT
REACTIVITY 0 0 2- MODERATE
PROTECTIVE     3- SERIOUS
EQUIPMENT     F 4- SEVERE

SECTION III - PHYSICAL DATA
APPEARANCE

SEMI-SOLID PASTE

 		ODOR

AMINE ODOR

 		BOILING POINT

N/A
SPECIFIC GRAVITY (H2O=1)

1.04

 		VAPOR PRESSURE (mm Hg.)

<5 MM

 		VOLATILE BY VOLUME (%)

NON-VOLATILE
VAPOR DENSITY (AIR=1)

N/A

 

 EVAPORATION RATE (BUAC=1)

<1

 		SOLUBILITY IN WATER

INSOLUBLE

SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT ( METHOD USED) FLAMMABLE LIMITS LEL UEL
212° F/100° C (PERCENT BY VOLUME) N/A N/A
FIRE EXTINGUISHING MEDIA

WATER FOG, FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL
SPECIAL FIRE FIGHTING PROCEDURES

USE SELF-CONTAINED BREATHING APPARATUS AND PROTECTIVE CLOTHING SHOULD BE WORN.
UNUSUAL FIRE AND EXPLOSION HAZARD

NONE

SECTION V - HEALTH HAZARD DATA
PRIMARY ROUTES OR ENTRY ___X__Inhalation ___X__Skin contact ______Eye contact ___X__Ingestion
EFFECT OF OVEREXPOSURE

INGESTION: MAY CAUSE STOMACH DISCOMFORT.

SKIN CONTACT: UNCURED PRODUCT MAY IRRITATE LIPS, GUMS, TONGUE AND SKIN.

EYE CONTACT: UNCURED PRODUCT WILL IRRITATE EYES.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE

NONE KNOWN.
EMERGENCY AND FIRST AID PROCEDURES

EYE: PRODUCT IS A SEMI-SOLID AND DIFFICULT TO GET INTO THE EYE. HOWEVER, IF PRODUCT DOE GET INTO THE EYE, RINSE WITH COPIOUS AMOUNTS OF WATER. IF IRRITATION DEVELOPS, SEEK MEDICAL ASSISTANCE.

SKIN: UNCATALYZED SILICONE RUBBER IS RELATIVELY INERT. FOR GOOD HYGIENE, WASH HANDS WITH SOAP AND WATER AFTER HANDLING.

INHALATION: UNCATALYZED SILICONE RUBBER DOES NOT EMIT VAPORS. REMOVE VICTIM FROM AREA OF EXPOSURE AND USE SUITABLE DUST MASK WHEN ADDING FILLERS AND PEROXIDES.

INGESTION: INDUCE VOMITING, SEEK MEDICAL ASSISTANCE.

SECTION VI - REACTIVITY
STABILITY UNSTABLE   CONDITIONS TO AVOID
  STABLE X AIR OR MOISTURE CAUSES POLYMERIZATION AND ACETIC ACID VAPORS ARE FORMED.
INCOMPATIBILITY (MATERIALS TO AVOID)
OXIDIZING MATERIAL CAN CAUSE A REACTION.
HAZARDOUS DECOMPOSITION PRODUCTS
SILICONE DIOXIDE, CARBON DIOXIDE AND TRACES OF INCOMPLETELY BURNED CARBON PRODUCTS.
HAZARDOUS
POLYMERIZATION		 MAY OCCUR   CONDITIONS TO AVOID
WILL NOT OCCUR X NONE

SECTION VII - SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED

SCRAPE PRODUCT FROM CONTAMINATED AREAS REMOVING RESIDUE PRODUCT WITH SOLVENT.
WASTE DISPOSAL METHOD

INCINERATE IN A 10% WASTE SOLVENT SOLUTION IN FURNACE FITTED WITH AN AFTERBURN AND SCRUBBER/OR BURY IN AN APPROVED CHEMICAL LANDFILL ACCORDING TO LOCAL, STATE AND FEDERAL REGULATIONS.

SECTION VIII - SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION (Specify type)

USE NIOSH/MSHA APPROVED RESPIRATOR WITH APPROPRIATE CARTRIDGE.
VENTILATION

PROVIDE ADEQUATE VENTILATION DURING CURING. USE SUITABLE DUST MASK WHEN ADDING FILLERS AND PEROXIDES. VAPORS FROM THE DECOMPOSITION OF PEROXIDES OCCUR DURING THE CURING.
PROTECTIVE GLOVES

YES

 		EYE PROTECTION

SAFETY GLASSES WITH SIDE SHIELDS
OTHER PROTECTIVE EQUIPMENT AND HYGIENIC PRACTICES

WORK UNIFORMS. MAINTAIN EYE WASH FOUNTAIN.

SECTION IX - SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING

STORE IN COOL, DRY PLACE IN TIGHTLY CLOSED CONTAINERS. AVOID BREATHING VAPORS FROM CURING. AVOID DIRECT OR PROLONGED CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. DO NOT EAT, DRINK OR SMOKE IN AREA.
OTHER PRECAUTIONS
This information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof.